Book Today!

 

 

What're your beliefs about How to Install a Bathtub?

Mounting a bathtub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently easily accessible, the project can relocate easily; if you need to open up a wall surface to remove the old bathtub and also position the brand-new tub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. Make certain you have qualified on your own for the work and are comfortable trying it. As opposed to employing a specialist to take control of a halfway-completed job, it is far better to consider using one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your bathroom if you have currently bought a brand-new bathtub and don't need to alter the plan of your previous water system pipelines.
Your devices and product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Preparing for the Installation

Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its final setting.

 

 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.

 

 

Setting up the Bathtub

Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To set up faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water system and examine all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bathtub and likewise check the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub needs to wait till the bathtub has actually been used at the very least when as this will resolve it right into its final setting.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Protect the faucet in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, resulting in problems with dampness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture rather early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the floor tiles using waterproof or water-proof sticky as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We were made aware of that article on A Step-by-Step Guide to Installing a Bathtub from someone on a different site. Do you know about another individual who is interested in the subject? Take a moment to promote it. Many thanks for your time spent reading it.

Request Service